Marley PH4AB Bedienungsanleitung PDF herunterladen (Seite 2)

GENERAL

Prior to operating heating, make sure the electrical outlet is of the configu-

ration and capacity appropriate for the heater.

When heater is wall or ceiling mounting, provisions must be made to bun-

dle or otherwise prevent excess power cord from draping loose.

In workshops, locate heater away from sources of wood dust.

FLOOR APPLICATION

The heater, as received, is set up for floor mounting. Place the heater on

floor or other flat surface and insert the plug into the proper wall outlet.

The heater can be adjusted to redirect the airstream. To do this, simply

loosen the knob on either side of the heater, then pivot heater to desired

position and re-tighten both knobs.

WALL MOUNT

SEE WARNING NO. 13.

This heater may be mounted on any wall that will support the weight of the

heater. First remove the mounting stand from the heater, then remove four

rubber grommets from stand. Secure stand to structural members of wall

with four 1/4” dia. X 1-1/2” long lag bolts (not provided). In masonry walls

use metal expansion shields or toggle bolts. Never use bolts smaller 1/4”

diameter.

Replace the heater in the stand and tighten knobs to lock in place. Two

large rubber washers go between heater and stand, one on either side.

REMEMBER: The electrical outlet must be within reach of the six foot

cord. Be sure to provide enough clearance to pivot heater and reach

adjustment knobs.

CEILING MOUNT

This heater may be mounted to any ceiling that will support the weight of

the heater.

First remove the mounting stand from the heater, then remove four rubber

grommets from stand. Secure stand to structural members of ceiling with

four 1/4” diameter bolts (not provided). In wood joist use 1-1/2” long lag

bolts. In steel beams use machine bolts secured with nuts and lockwash-

ers. Never use bolts smaller than 1/4” diameter.

Replace the heater in the stand and tighten knobs to lock in place. Two

large rubberwashers go between heater and stand, one on either side.

REMEMBER: The electrical outlet must be within reach of the six foot

cord. Be sure to provide enough clearance to pivot heater and reach

adjustment knobs.

HEATER OPERATION

To operate the heater, first select either high or low position on the heat

selector switch, then turn the thermostat knob as far as it will go in the

clockwise direction. The indicator light will come on and remain on as long

as the heater is in the operating mode. when the room temperature reach-

es the desired level, slowly turn the thermostat knob counterclockwise until

the thermostat clicks. The heater off, turn thermostat knob as far as it will

go in the counterclockwise direction until the indicator light is off.

The fan selector switch allows continuous or cycling fan operation by

selecting either the “ON” or “Auto” position, respectively.

CLEANING AND STORAGE

Turn thermostat off, then remove plug from electrical outlet before cleaning

heater. Use a soft cloth for dusting. For cleaning use only a damp rag and

nonabrasive dish detergent. Do not use abrasive or chemical cleaners as

these may harm the finish.

If heater is used in a very dusty location, use a vacuum cleaner dust brush

to remove dust and other foreign material from the grilles.

Always unplug cord and wrap around heater when not in use. Move floor

mounted heaters to a safe location for storage.

SERVICE

This heater does not require any routine maintenance other than occa-

sional cleaning to prevent clogging of intake grille opening. To clean air

intake grille, use vacuum with brush attachment or high pressure air. The

motor is permanently lubricated.

Do not operate the heater with a damaged cord or plug or if the heater mal-

functions or has been damaged in any manner. Return heater to autho-

rized service facility for examination, electrical, or mechanical adjustment,

or repair.

Call the toll-free number listed for assistance in locating the Marley autho-

rized service center in your area.

TO PREVENT HEATER FROM POSSIBLY FALLING, DO NOT USE

KEYHOLE SLOTS FOR CEILING MOUNT APPLICATION. SEE ALSO

WARNING NO. 13.

WARNING

BE CAREFUL NOT TO DIRECT THE AIRSTREAM AT DRAPERIES,

FURNITURE, OR OTHER OBJECTS THAT COULD BE DAMAGED BY

HEAT. DO NOT USE HEATER ON FLOOR WITHOUT STAND IN

PLACE. DO NOT SUE THE HEATER WHERE A SMALL CHILD MAY

FALL OVER THE HEATER. DO NOT PLACE THE HEATER WHERE

THE POWER CORD MAY BE WALKED ON, TRIPPED OVER, OR OTH-

ERWISE SUBJECTED TO HARD USAGE.

WARNING

LEMENTS FRONT

MIDDLE

REAR

HEAT SW.

LOW

AUTO

FAN SW.

TERMINAL BLOCK

INDICATOR LIGHT

OFF

CYL

THERMOSTAT

MANUAL RESET

THERMAL UNIT

MOTOR

KEYHOLE

SLOT

MOUNTING

HOLES

ARE 16” O.C.

USE

KEYHOLES

FOR WALL

MOUNTING

IRCULAR

HOLE

USE CIRCULAR

HOLES FOR

CEILING

MOUNTING.

DO NOT USE

KEYHOLES.

1 2 3 4 5 6 7 ... 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Marley PH4AB Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern